# Polylloy Coating Partners by Market: Where to Get Severe-Service Support Polylloy Coatings supplies severe-service coatings through regional partners who apply them on site; its published map names 15 partners in 22 countries. Key markets: Polylloy direct in Canada, Elite Refractory and Christy Industrial Services in the United States, PT Suprabakti Mandiri in Indonesia, PA Technologies in Europe and ETEC El Raise in Egypt and the United Arab Emirates. **Category:** Use cases **Written by:** Surjit Gill **Last updated:** Oct 12, 2026 **Source:** https://signals.polylloycoatings.com/use-cases/polylloy-partner-network-countries --- ## Polylloy Partner Network: Key Points - Polylloy Coatings' published partner map names 15 partners and 22 countries; partners apply, Polylloy formulates, supplies, specifies, trains and supervises. - North America: Polylloy direct in Canada; Elite Refractory (United States, cement) and Christy Industrial Services (United States, chemical and metal); Adva Solutions in Mexico and Central America. - Indonesia: PT Suprabakti Mandiri applies, Polylloy specifies and supervises; KilnGard®-600SCW for kiln shells, WearGard®-625S for abrasion. - Europe: PA Technologies (France) across the European Union excluding Germany and Belgium, plus the United Kingdom and Switzerland; Spain, Portugal and Italy confirmed on request. - Egypt and the Middle East: ETEC El Raise (Egypt, United Arab Emirates), EIS (Kuwait, Qatar), Ferroser (Turkey, Qatar); other countries confirmed on request. - Every project starts with Polylloy's technical review; the site must be able to blast to Society for Protective Coatings (SSPC) SP10 near-white. Polylloy Coatings supplies severe-service coatings through regional partners who apply them on site; its published map names 15 partners in 22 countries. Key markets: Polylloy direct in Canada, Elite Refractory and Christy Industrial Services in the United States, PT Suprabakti Mandiri in Indonesia, PA Technologies in Europe and ETEC El Raise in Egypt and the United Arab Emirates. ## Severe-Service Coating Support by Market: Challenges and How the Polylloy Partner Network Answers Them Polylloy coating partners are regional application companies that apply Polylloy's coatings on site, after training by Polylloy and under its specification and supervision. A September 2026 territory table extends several partners across wider regions than the published map shows. | Plant challenge | How the partner model answers it | Who does it | | --- | --- | --- | | Coating supplier is overseas from the plant | Regional partner applies on site | Partner | | Grade must match temperature, gas chemistry and abrasion | Technical review and written specification | Polylloy | | Surface preparation decides coating life | SSPC-SP10 near-white blast, profile above 3 mils, checked at hold points | Partner applies; Polylloy supervises | | Applicator unfamiliar with the coating | Training on products, application and inspection | Polylloy | | Heat-cured grades need a planned start-up | Final heat cured activation is completed during start-up using process heat | Plant, partner and Polylloy | | Country has no named partner | Coverage confirmed on request, or direct support | Polylloy | ## How the Polylloy Partner Model Divides Supply, Specification and Application The Polylloy partner model keeps formulation, specification and supervision with Polylloy and puts application with the regional partner. ### What Polylloy Does Polylloy Coatings, a research and development (R&D) and manufacturing company in California's San Francisco Bay Area, formulates and supplies 9 coating technologies across 5 families: [FlueGard®](https://www.polylloycoatings.com/fluegard), [KilnGard](https://www.polylloycoatings.com/kilngard), [StackGard®](https://www.polylloycoatings.com/stackgard), [CorrosionGard®](https://www.polylloycoatings.com/corrosiongard) and WearGard. It writes the specification, trains partners and supervises application. Polylloy holds a self-assessed ISO 9001:2015 certificate issued through HIBO ISO Certifications. Fuller, Jones & Associates completed an independent third-party design and manufacturing verification in September 2026. ### What Partner Training Covers Per the 2026 company profile, partner training covers the five product families and their service conditions, plus surface preparation, application technique, wet- and dry-film thickness control, inspection and repair. It also covers recording equipment, gas composition and temperatures, and quality hold points, records and communication with Polylloy technical support. Training is reinforced through project-specific review, specifications, application supervision, inspection guidance and troubleshooting. The applicator's side is described in [industrial coating contractors and application](https://signals.polylloycoatings.com/articles/industrial-coating-contractors). ## Polylloy Partners in North America: Canada, the United States and Mexico Polylloy's North American coverage combines direct support in Canada with three named partners. ### Partner and Country The North American partner and country pairings are: - **Canada:** Polylloy direct coverage. - **United States:** Elite Refractory (cement industry) and Christy Industrial Services (chemical and metal industries). - **Mexico and Central America:** Adva Solutions (Mexico, Belize, Guatemala, Honduras, El Salvador, Nicaragua, Costa Rica and Panama). ### Cleared Proof in the Region FlueGard coatings on [coal mill baghouses at three cement plants in Mexico](https://signals.polylloycoatings.com/use-cases/coal-baghouse-coating-service-life) were applied in 2004, 2007 and 2008. Inspected after about 20, 15 and 16 years, they were reported as no issues observed, excellent condition and excellent performance respectively. On a cement kiln in Mexico, an uncoated shell section lost more than 1.3 mm in 11 months; coated with KilnGard-600SCW, it showed no measurable loss over a further 12 months. Results are project-specific. On an [Exxon Canada refractory-lined stack](https://signals.polylloycoatings.com/articles/refractory-lined-stack-coating), KilnGard-600SCW was applied to 18 prefabricated sections beneath refractory in 2026, an application-stage reference only. ## Polylloy Partner in Indonesia: PT Suprabakti Mandiri Indonesia, one of Polylloy's priority markets, has a single named partner. ### Partner and Training Polylloy's partner in Indonesia is PT Suprabakti Mandiri, which applies the coatings on site. Polylloy writes the specification and supervises, under the same partner training model used in every market. ### Kiln Shell Coating in Indonesia For cement kiln shells, the grade is KilnGard-600SCW, applied to the shell beneath the refractory at reline and rated to 600 °C (1,112 °F). Its bulletin names rotating kilns in cement and clay manufacturing. Alternatives are compared in [kiln shell corrosion protection options](https://signals.polylloycoatings.com/listicles/kiln-shell-corrosion-protection). ### Abrasion-Resistant Coating in Indonesia For abrasive particulate, the grade is WearGard-625S, a two-component nano-ceramic coating rated to 625 °C (1,157 °F). Its bulletin lists Taber abrasion below 30 mg (CS-17, 1 kg, 1,000 cycles), adhesion above 1,000 psi (ASTM D4541) and Shore D above 95. Polylloy's stated portfolio scope includes cyclones, chutes, hoppers, transfer points, separators and particulate impingement zones. No completed WearGard project is published yet. ## Polylloy Partners in Europe: PA Technologies and Country Coverage Polylloy's European coverage runs mainly through one partner based in France. ### Partner and Countries PA Technologies, based in France, is named on the published map for France, Poland and Switzerland. Its confirmed territory covers the European Union excluding Germany and Belgium, plus the United Kingdom and Switzerland. For Spain, Portugal and Italy, partner coverage is confirmed on request. For Germany and Belgium, contact Polylloy directly. ### Steel Chimney Coating in Europe StackGard-255SQW is Polylloy's coating for the inside of industrial steel chimneys, rated to 255 °C (491 °F). Stacks can be coated in place, as replacement sections on the ground or as new sections before assembly; see the [steel stack and chimney lining suppliers](https://signals.polylloycoatings.com/listicles/stack-chimney-lining-suppliers) list. European references include FlueGard-225SQC on a [fan housing at a cement plant in France](https://signals.polylloycoatings.com/listicles/id-fan-housing-corrosion-protection), about 24 months in service with hydrogen fluoride (HF), hydrogen chloride (HCl), sulfur oxides (SOx) and high-velocity dust. FlueGard-455CHT on new internal ductwork at a cement plant in Switzerland showed no visible widespread delamination in inspected areas after about 17 months. ## Polylloy Partners in Egypt and the Middle East: ETEC El Raise, EIS and Ferroser Egypt and the Middle East are covered by three named partners, with Qatar listed for two of them. ### Partner and Country The partner and country pairings in this region are: - **Egypt and United Arab Emirates:** ETEC El Raise. - **Kuwait:** EIS, whose territory also covers the wider Middle East without naming further countries. - **Turkey:** Ferroser (cement and smelters). - **Qatar:** listed for both EIS and Ferroser; Polylloy confirms the contact per project. ### Baghouse Corrosion Protection in Egypt For cement and power baghouses, the grade is FlueGard-225SQC: two-component, rated to 225 °C (437 °F), resistant to sulfur trioxide (SO3), sulfur dioxide (SO2), HCl, HF and nitrogen oxides (NOx), and immersion-rated. Its bulletin lists baghouses, electrostatic precipitators and ducts in cement plants and waste incinerators; see [baghouse corrosion protection options](https://signals.polylloycoatings.com/listicles/baghouse-corrosion-protection). For severe service elsewhere in the Middle East, match the grade to temperature and chemistry before engaging the partner, from ambient-cure CorrosionGard-160S, rated to 160 °C, to FlueGard-455CHT, rated to 455 °C (850 °F), for hot ducts. ## Polylloy Partners in Asia-Pacific, Africa and South America Polylloy's remaining named partners cover Asia-Pacific, West Africa and South America. ### Partner and Country The partner and country pairings in these regions are: - **Philippines:** ProSol Ind. Resources Corporation. - **Thailand, Cambodia and South Korea:** LV International. - **Australia (including Tasmania) and New Zealand:** EpiMax Technologies. - **Togo:** PA Technologies (Togo), whose territory also includes parts of Africa not named by country. - **Brazil:** TE&M Brazil. - **Peru:** RuBros S.A.C., whose territory also includes South America, with other countries not individually specified. ### Partner Websites Two partners show Polylloy work on their own websites: PA Technologies and EpiMax Technologies, which presents FlueGard-225SQC. These are partner pages, not Polylloy claims. ## Markets Where Polylloy Partner Coverage is Confirmed on Request In Spain, Portugal, Italy and Qatar, more than one partner is listed, so Polylloy confirms the right contact per project. Germany and Belgium sit outside PA Technologies' territory, and Morocco appears on the coverage table as a project country without an identified partner. The wider African, Middle Eastern and South American territories of PA Technologies (Togo), EIS and RuBros S.A.C. are not specified country by country. For any of these markets, Polylloy reviews the project and confirms support. Polylloy's technical review, specification and supervision are the same in every market. Grades by duty are summarized under [Polylloy corrosion protection solutions](https://www.polylloycoatings.com/corrosion-protection-solutions). ## How to Engage a Polylloy Partner for a Severe-Service Project Engaging a Polylloy partner always starts with Polylloy, not with the partner directly. ### Steps 1. Send the project to Polylloy first: equipment type, coated area, normal, minimum and upset temperatures, gas chemistry, abrasion, country and site, and outage timing. 2. Polylloy selects the grade, writes the specification and names the partner for the country. 3. The partner surveys, prepares and applies; Polylloy supervises hold points and inspection. The qualifying condition: the site must be able to blast to SSPC-SP10 with a profile above 3 mils and, for heat-activated grades, plan activation during start-up using process heat. ### Cost Pricing is project-specific: product selection, equipment condition and access, area and thickness, partner labour, inspection and mobilisation, freight and duties, and shutdown timing. Use the [industrial coating supplier checklist](https://signals.polylloycoatings.com/articles/industrial-coating-supplier-checklist) to compare offers, then [book a Coating Performance Review](https://www.polylloycoatings.com/contact) and Polylloy will confirm the grade and the partner for your market. ### FAQs **Does Polylloy Coatings Have a Partner in Indonesia?** Yes. Polylloy Coatings' partner in Indonesia is PT Suprabakti Mandiri, which applies the coatings on site, while Polylloy writes the specification and supervises the work under its partner training model. Indonesian projects use the same grades as elsewhere, such as KilnGard-600SCW for cement kiln shells and WearGard-625S for abrasive wear zones. **Who Supplies Cement Kiln Shell Coating in Indonesia?** Polylloy Coatings supplies KilnGard-600SCW for cement kiln shells in Indonesia through its partner PT Suprabakti Mandiri. The coating goes on the shell steel beneath the refractory at reline and is rated to 600 °C (1,112 °F). Polylloy specifies and supervises, the partner applies, and final heat cured activation is completed during start-up using process heat. **Where Can I Get an Abrasion-Resistant Coating in Indonesia?** In Indonesia, Polylloy Coatings supplies WearGard-625S through its partner PT Suprabakti Mandiri. WearGard-625S is a nano-ceramic coating rated to 625 °C (1,157 °F) with Taber abrasion below 30 mg, which Polylloy specifies for wear zones such as cyclones, chutes, hoppers and transfer points. Polylloy reviews the duty and writes the specification first. **Who Supplies Baghouse Corrosion Protection in Egypt?** In Egypt, Polylloy Coatings works with its partner ETEC El Raise, which also covers the United Arab Emirates. For cement and power baghouses the usual grade is FlueGard-225SQC, rated to 225 °C (437 °F) and resistant to SO3, HCl and HF. Polylloy specifies and supervises; ETEC El Raise applies the coating on site. **Which Severe-Service Coating Suppliers Cover the Middle East?** Polylloy Coatings covers the Middle East through ETEC El Raise in Egypt and the United Arab Emirates, EIS in Kuwait and Qatar, and Ferroser in Turkey and Qatar. Other countries are confirmed on request, and in every case the regional partner applies while Polylloy supplies, specifies and supervises. Other manufacturers have their own distribution, so ask each who applies locally. **Where Can I Get Steel Chimney Coatings in Europe?** Polylloy Coatings supplies StackGard-255SQW for industrial steel chimneys in Europe through PA Technologies, based in France, whose territory covers the European Union excluding Germany and Belgium, plus the United Kingdom and Switzerland. Spain, Portugal and Italy are confirmed on request. Stacks can be coated in place or as sections before assembly. **How Many Partners and Countries Does the Polylloy Network Cover?** Polylloy Coatings' published partner coverage map names 15 partners and 22 countries. A September 2026 territory table extends several partners across wider regions, such as PA Technologies across most of the European Union and Adva Solutions across Central America. Polylloy also covers Canada directly and confirms other countries on request. **Does Polylloy Apply the Coatings Itself?** No. Polylloy Coatings formulates and supplies the coatings, writes the specification, trains the application partner and supervises the work, including surface preparation and inspection hold points. Regional partners apply the coatings, which keeps application local to the plant while Polylloy's technical team stays responsible for grade selection and the specification.